2011 C4S Condensers

[eastwood1875]

Hi Chaps!

Have been advised by my OPC in Solihull that I have a leaky n/s condenser (stone damage) I'm based in Redditch so after some googling last night I found a specialist very close to me called 'Pro-9'. Does anyone have any dealing with these guys? They submitted a very competitive quote to replace both condensers and re-gas - roughly half the price of Solihull. I work in West Brom so Ramus Porsche would be convenient too. Any reviews for Pro-9 and Ramus?

Thanks in advance,

Darren

 

[Lancerlot]

If your vehicle is covered by Porsche extended warranty, you will need to make sure the Indy is fitting Porsche approved parts.
Regards,

Clive

 

[tscaptain]

And then get some grilles fitted to prevent it happening again![]

 

[STiG911]

Replacing the condensers is a job an even halfway competent mechanic can do, and even a lot of DIYers do it with no problems. Like Clive said, long as the parts used are OK with Porsche, you get the work done anywhere. And yes - fit grilles!

 

[JCX]

The junk in my rads even after careful cleaning with bumper on.

 

[JCX]

Before my grills were fitted...

 

[JCX]

After the grills were fitted... subtle but super.

 

[eastwood1875]

Thanks Guys! Very helpful indeed, didn't expect that many replies
I do have an active extended warranty although I am running an x-pipe, lowering springs and fatter spacers. Fingers crossed I have never had a warranty claim denied although the claims I have had did not relate to my 'mods'. I will check with Pro-9 to see if they use OE parts and will ask them to fit the protector grills.

All the best!

Darren

 

[eastwood1875]

Grills look good!

Nice job.

Darren

 

[JCX]

Grills look good!

Nice job.

Darren

I used the Rennline grills. Beautiful but expensive (relatively).

 

[eastwood1875]

JCX, They look worth the extra. Can you send me the part number/s please?

design 911 job?

Darren

 

[Lancerlot]

https://www.porscheclubgb.com/forum/tm.aspx?m=613041
Regards,

Clive

 

[JCX]

JCX, They look worth the extra. Can you send me the part number/s please?

design 911 job?

Darren

Hi Darren,
I ordered mine from the states.
"http://www.rennline.com/R...productinfo/E1001/2236|2240|2246|2247"
this link should get you to them. You will have import duty to pay...
Best
Joe

 

[eastwood1875]

Thanks both. Pro-9 have confirmed they will be using OE components and will fit the mesh kit if I supply it. Will get it booked in before the weather warms up and once I have paid for my front discs and pads and wheel painting at POC Solihull!

Really appreciate all your help.

Darren

 

[JCX]

[][s2]

 

[Ianstewartshouse1]

Thanks Guys! Very helpful indeed, didn't expect that many replies
I do have an active extended warranty although I am running an x-pipe, lowering springs and fatter spacers. Fingers crossed I have never had a warranty claim denied although the claims I have had did not relate to my 'mods'. I will check with Pro-9 to see if they use OE parts and will ask them to fit the protector grills.

All the best!

Darren

Wow you are lucky your OPC is so tolerant have heard horror stories about OPCs being very strict. Even the grills you talk about or wired in dash cams have been the subject of a number of discussions where certain OPCs refused to renew warranty, your renewal with all those adds sounds like a mini miracle!

 

[eastwood1875]

Hi Ian,
Just to clarify for you. My car was standard when purchased last June with the extended warranty. Mods were fitted afterwards but I have had warranty work carried out since without question. However I can't imagine passing the 111 point check when it comes up for renewal the year after next.

Daz

 

[Ianstewartshouse1]

Hi Daz, that makes sense!